One Ton Taper Tie Rod Insert

Tapered Steering Knuckle Insert

Your Price: $5.00

If you are going from heim joints to tie rod ends on your steering or if you are flipping your tie rod to the top of the knuckle, then our tapered steering knuckle insert is the part you need.

Part Number: OSST90

LEAD TIME: In Stock & ready to ship.

Quantity

Description & Installation Instructions
Customer Reviews
Questions and Answers

If you are going from heim joints to tie rod ends on your steering or if you are flipping your tie rod to the top of the knuckle, then our tapered steering knuckle insert is the part you need. All you need is a 7/8" hole to put the insert in, and you have the proper taper for a GM 1 ton tie rod end (7° or 1.5" per ft.). From the lip down this measures 3/4 inches. These are sold individually. This insert will not work with the high angle tie rod end! (ES2026R)

Q: will these tapered inserts work with the tie rods under the knuckle? I purchased the gm 1 ton conversion kit for a 1995 Cherokee

Asked by: james - 4/1/2019

A: Thanks for the question. Yes, these inserts can work for both over the knuckle and under the knuckle applications.

Answer provided by: Joe Ledford (4/4/2019)

Submit an answer

Q: I am trying to repair my steering knuckle because it appears that the taper is larger than what it is supposed to be. What is the inner diameter of the large end of the taper?

Asked by: Michael - 2/4/2020

A: This inserts widest point is going to be .74 of an inch. That being said the insert is slotted and this will vary slightly by the hole drilled in the knuckle.

Answer provided by: Clayton Arrowood (2/5/2020)

Submit an answer

Q: Hello! Is this the insert needed for my stock 2015 Jeep JK pitman arm and GM 1ton draglink ends? Thanks!

Asked by: Brandon - 6/3/2019

A: Our no drill kit (PartNo: B4WK12293) doesn't require any inserts or drilling if running your drag link under the knuckle. If you plan to run your drag link over the knuckle you will need to drill your passenger side knuckle to 7/8" and add a tapered insert.

Answer provided by: Conner (6/4/2019)

Submit an answer

Q: I have a 2006 Chrysler Pacifica AWD. Replacing the tie rod end on the drivers side I discovered the tapered hole on the knuckle the tie rod goes into is wallowed out, no longer usable. Do you have a tapered bushing I could use to repair this?

Asked by: Tim - 6/11/2019

A: We do have those! They are currently out of stock and expected to be back in stock in around 2 weeks. Check back with us and we'll get you set up!

Answer provided by: Conner (6/11/2019)

Submit an answer

Q: I am looking for an insert like this for a 1977 f150 do you offer something like that? Thanks

Asked by: Derek Sehi - 10/22/2019

A: No unfortunately we do not.

Answer provided by: Clayton Arrowood (10/22/2019)

Submit an answer

Q: Do you have to weld these in like many others on the market?

Asked by: Shae - 2/13/2020

A: They may be pressed in or welded. We have had customers do both.

Answer provided by: Tommy Bell (2/14/2020)

Submit an answer

Q: Would this fit a 3/4 ton steering knuckle but keep it 3/4 ton?

Asked by: Joe - 8/27/2020

A: This is intended for a GM 1 ton taper tie rod end (7° or 1.5" per ft.)

Answer provided by: Clayton Arrowood (8/31/2020)

Submit an answer

Q: Looking for a 7 degree tapered insert for a Ford 11/16 tie rod. The taper is from .63 large to .56 small with 1/2 inch stud for pitman arm. Going from heim to tie rod

Asked by: Flathead 8 - 10/19/2020

A: The bore is .75" at the top, .644 an the bottom and is .85" tall

Answer provided by: Clayton Arrowood (10/22/2020)

Submit an answer

Q&A

7/8-18 Jam Nut Right Hand Thread (For use with Tie Rod Ends)

$1.80

In Stock & ready to ship.

(1)

Add to Build Sheet

Add To Cart

Steering>Tie Rod End Steering Kits

Tapered Steering Knuckle Insert

Rating Snapshot

Average Customer Ratings

Q: will these tapered inserts work with the tie rods under the knuckle? I purchased the gm 1 ton conversion kit for a 1995 Cherokee

Q: I am trying to repair my steering knuckle because it appears that the taper is larger than what it is supposed to be. What is the inner diameter of the large end of the taper?

Q: Hello! Is this the insert needed for my stock 2015 Jeep JK pitman arm and GM 1ton draglink ends? Thanks!

Q: I have a 2006 Chrysler Pacifica AWD. Replacing the tie rod end on the drivers side I discovered the tapered hole on the knuckle the tie rod goes into is wallowed out, no longer usable. Do you have a tapered bushing I could use to repair this?

Q: I am looking for an insert like this for a 1977 f150 do you offer something like that? Thanks

Q: Do you have to weld these in like many others on the market?

Q: Would this fit a 3/4 ton steering knuckle but keep it 3/4 ton?

Q: Looking for a 7 degree tapered insert for a Ford 11/16 tie rod. The taper is from .63 large to .56 small with 1/2 inch stud for pitman arm. Going from heim to tie rod

Related Items

Browse Similar Items

Mailing List